Finite element analysis of cure in a rubber cylinder

The variation of temperature inside a rubber cylinder was recorded during vulcanization in a mould. The results were compared with those obtained by solving the transient heat equation by a finite element technique. Heat generation during cure was considered by means of first-order curing kinetics w...

Descripción completa

Guardado en:

Detalles Bibliográficos
Autor principal:	Marzocca, A.J.
Formato:	JOUR
Materias:	finite element simulation heat transfer rubber state of cure Chemical Reactions - Reaction Kinetics Heat Transfer - Mathematical Models Mathematical Techniques - Finite Element Method Polymers - Curing Curing Kinetics Transient Heat Equation Vulcanization
Acceso en línea:	http://hdl.handle.net/20.500.12110/paper_00323861_v32_n8_p1456_Marzocca
Aporte de:	Biblioteca Digital - Facultad de Ciencias Exactas y Naturales (UBA) de Universidad de Buenos Aires

Ejemplares similares

Finite element analysis of cure in a rubber cylinder
Publicado: (1991)

About the cure kinetics in natural rubber/styrene Butadiene rubber blends at 433 K
por: Mansilla, M.A., et al.

About the cure kinetics in natural rubber/styrene Butadiene rubber blends at 433 K
por: Mansilla, Marcela Angela, et al.
Publicado: (2012)

Vulcanization kinetic of styrene-butadiene rubber by sulfur/TBBS
por: Marzocca, A.J., et al.

Vulcanization kinetic of styrene-butadiene rubber by sulfur/TBBS
por: Marzocca, Angel José, et al.
Publicado: (2006)

An analysis of the influence of the accelerator/sulfur ratio in the cure reaction and the uniaxial stress-strain behavior of SBR
por: Marzocca, J., et al.

Cure kinetics and swelling behaviour in polybutadiene rubber
por: Marzocca, A.J., et al.

Cure kinetics and swelling behaviour in polybutadiene rubber
por: Marzocca, Angel José, et al.
Publicado: (2010)

An analysis of the influence of the accelerator/sulfur ratio in the cure reaction and the uniaxial stress-strain behavior of SBR
Publicado: (2004)

The finite element method in heat transfer and fluid dynamics /
por: Reddy, J. N. (Junuthula Narasimha), 1945-
Publicado: (1994)

The finite element method in heat transfer and fluid dynamics /
por: Reddy, J. N. (Junuthula Narasimha), 1945-, et al.
Publicado: (2010)

A SAXS and swelling study of cured natural rubber/styrene-butadiene rubber blends
por: Salgueiro, W., et al.

Cure kinetics and shrinkage model for epoxy-amine systems
Publicado: (2005)

Cure kinetics and shrinkage model for epoxy-amine systems
por: Ramos, J.A., et al.

A SAXS and swelling study of cured natural rubber/styrene-butadiene rubber blends
Publicado: (2009)

Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers
por: Mansilla, M.A., et al.

Evolution of the free volume and glass transition temperature with the degree of cure of polybutadiene rubbers
Publicado: (2013)

Effect of electron-beam irradiation on the thermal vulcanization of a natural rubber compound
por: Espósito, L.H., et al.

Cure temperature influence on natural Rubber - A small angle X-ray scattering study
por: Salgueiro, W., et al.

Numerical simulation of cooling rates in vitrification systems used for oocyte cryopreservation
por: Sansinena, Marina, et al.
Publicado: (2011)

Supercloseness on graded meshes for Q1 finite element approximation of a reaction-diffusion equation
por: Duran, Ricardo Guillermo, et al.
Publicado: (2013)

Supercloseness on graded meshes for Q1 finite element approximation of a reaction-diffusion equation
por: Durán, R.G., et al.

Error estimates for anisotropic finite elements and applications
por: Duran, Ricardo Guillermo
Publicado: (2006)

Error estimates for anisotropic finite elements and applications
por: Durán, R.G.

Effect of electron-beam irradiation on the thermal vulcanization of a natural rubber compound
Publicado: (2019)

Cure temperature influence on natural Rubber - A small angle X-ray scattering study
Publicado: (2007)

Influence of the cure level on the monomeric friction coefficient of natural rubber vulcanizates
por: Marzocca, A.J., et al.

Influence of carbon black dispersion on the thermal diffusivity of an SBR vulcanizate
por: Goyanes, S.N., et al.

Influence of carbon black dispersion on the thermal diffusivity of an SBR vulcanizate
por: Goyanes, Silvia Nair, et al.
Publicado: (1999)

Natural rubber/styrene-butadiene rubber blends prepared by solution mixing: Influence of vulcanization temperature using a Semi-EV sulfur curing system on the microstructural properties
por: Mansilla, M.A., et al.

Influence of the cure level on the monomeric friction coefficient of natural rubber vulcanizates
Publicado: (2004)

Analysis of variation of molecular parameters of natural rubber during vulcanization in conformational tube model. II. Influence of sulfur/accelerator ratio
por: Cerveny, S., et al.

Analysis of variation of molecular parameters of natural rubber during vulcanization in conformational tube model. II. Influence of sulfur/accelerator ratio
por: Cerveny, Silvina, et al.
Publicado: (1999)

Natural rubber/styrene-butadiene rubber blends prepared by solution mixing: Influence of vulcanization temperature using a Semi-EV sulfur curing system on the microstructural properties
Publicado: (2017)

Thermal properties in cured natural rubber/styrene butadiene rubber blends
por: Goyanes, S., et al.

Experimental study of free convective mass transfer in porous media
por: Gabitto, Jorge Federico, et al.
Publicado: (1981)

Experimental study of free convective mass transfer in porous media
por: Gabitto, J.F., et al.

Thermal properties in cured natural rubber/styrene butadiene rubber blends
por: Goyanes, Silvia Nair, et al.
Publicado: (2008)

Nanohole volume dependence on the cure schedule in epoxy thermosetting networks: A PALS study
por: Goyanes, Silvia Nair
Publicado: (2006)

Nanohole volume dependence on the cure schedule in epoxy thermosetting networks: A PALS study
por: Salgueiro, W., et al.